Что такое обработка точек останова с ЧПУ и как ее освоить?

CNC breakpoint machining is a critical rescue technology in precision manufacturing, enabling machines to resume operations from the exact interruption point after unexpected issues like tool breakage, power outages, or program errors. Without proper mastery of this process, manufacturers face costly scrap, extended downtime, and compromised part accuracy. This article breaks down core causes of interruptions, Пошаговые решения, system-specific operations, and key technical tips to help engineers minimize losses and optimize efficiency.

1. What Causes CNC Machining Interruptions? And How to Respond?

Interruptions in CNC machining often stem from three main issues: поломка инструмента, power outages, and program errors. Each requires targeted, time-sensitive responses to protect the workpiece and avoid rework. Ниже приведен causal chain + step-by-step guide for each scenario:

1.1 Tool Breakage: The Most Common Interruption

Поломка инструмента (from material hardness, excessive feed rate, or worn tools) demands immediate action to prevent collision or surface damage. Follow this linear process:

1. Emergency Stop: Press the “feed hold button” or “emergency stop switch” immediately—never use the reset key (it erases breakpoint position data).
2. Запись данных: If the machine lacks breakpoint protection, manually note:

• Interrupted program segment number (НАПРИМЕР., N120).
• Exact XYZ coordinates of the tool tip at the breakpoint.

3. Tool Replacement & Параметр: Install a new tool, затем выполнить Z-axis tool setting only (to maintain consistent relative position with the workpiece—avoid re-setting X/Y axes, which risks misalignment).
4. Program Adjustment: Modify the program header:

• Input the recorded XYZ coordinates as the new start point.
• Delete redundant program segments before the breakpoint (НАПРИМЕР., delete N1-N119 if interrupted at N120).

1.2 Power Outage: Coordinate System Determines Recovery Difficulty

Power outages erase temporary data, so the type of workpiece coordinate system used dictates how to resume:

1.3 Программные ошибки: Syntax vs. Logic Issues

Ошибки программы вызывают сбои, когда система ЧПУ не может интерпретировать команды.. Различайте и исправляйте их:

2. How to Operate Breakpoint Machining on Typical CNC Systems?

Different CNC systems (НАПРИМЕР., Mitsubishi, Shindaiwa) have unique operation flows. Ниже step-by-step examples for two widely used systems:

2.1 Mitsubishi M80 System (Emergency Tool Change Scenario)

1. Press the reset button to stop all active commands.
2. Perform three-axis homing (return to machine origin) to re-establish reference positions.
3. Replace the broken tool, then enter the new tool’s compensation value (длина, radius) into the tool offset page.
4. Clear XY relative coordinates (set to 0) to reset position reference.
5. Start the spindle at the required speed (НАПРИМЕР., 3000 Rpm) to prepare for cutting.
6. Переключиться на MDI mode (Manual Data Input), then use the “restart” function to search for the breakpoint segment.
7. Confirm the tool tip aligns with the recorded XYZ coordinates, then start machining.

Key Safety Tip: Lift the spindle to a safe height (10-20mm above the workpiece) before starting—prevents accidental collision if coordinates are slightly off.

2.2 New-Generation Systems (Rapid Resumption)

Современные системы ЧПУ (НАПРИМЕР., Fanuc 0i-F Plus) simplify breakpoint machining with one-click functions:

1. Enter the “Machining Information Settings” page to view the automatically recorded breakpoint line number (НАПРИМЕР., N250).
2. Press F4 (or designated key) to set this line number as the start of the single-block run.
3. The system automatically searches for N250 and positions the tool at the corresponding XYZ coordinates.
4. Adjust pre-set parameters (breakpoint position, cutting depth, feed speed) При необходимости, then start the program.

Efficiency Tip: Pre-configure common parameters (НАПРИМЕР., скорость корма 80% of normal) in the system to reduce setup time during resumption.

3. Key Technical Tips to Avoid Breakpoint Machining Failures

Even with correct operation, ignoring technical details can lead to poor part quality or re-interruption. Следуйте этим critical guidelines:

3.1 Modal Instruction Handling

Modal instructions (НАПРИМЕР., G01 for linear interpolation, F for feed rate) remain active until canceled. If the breakpoint’s XYZ coordinates are not explicitly defined:

• Look up the nearest valid modal instruction (НАПРИМЕР., use the F150 feed rate from N110 if N120 lacks a feed rate value).
• Never assume modal values—verify with the program log to avoid over-cutting.

3.2 Охлаждающая жидкость & Cutting Parameter Matching

Proper parameter setting reduces tool breakage (the root cause of most breakpoints). Match parameters to material characteristics:

3.3 System Differentiation Adaptation

Avoid “one-size-fits-all” operation:

• Mitsubishi Systems: Require manual homing after power outages—skip this step, and coordinates will be inaccurate.
• Shindaiwa Systems: Automatically save breakpoint data for 24 hours after power loss—use this window to resume without re-measuring.
• Fanuc Systems: Need “breakpoint memory” to be enabled in parameters (set P1001=1) to store position data.

Yigu Technology’s Perspective on CNC Breakpoint Machining

В Yigu Technology, Мы видим CNC breakpoint machining as a “loss-control lifeline” rather than just a rescue tool. Many manufacturers waste time on rework because they skip data recording or ignore system differences. We advocate a “prevention + rapid response” strategy: 1) Pre-configure breakpoint protection parameters (НАПРИМЕР., enable automatic data saving) to reduce recovery time; 2) Train operators to record XYZ coordinates в пределах 5 минуты of interruption—this cuts resumption time by 40%; 3) Use simulation software to test modified programs, avoiding secondary errors. For clients with high-volume production, we also provide customized breakpoint monitoring systems that alert operators to tool wear (a leading cause of breakage) в реальном времени.

Часто задаваемые вопросы (Часто задаваемые вопросы)

1. Q.: After a power outage, can I skip three-axis homing and directly input the recorded XYZ coordinates?

А: Нет. Power outages may cause slight mechanical drift—homing re-establishes the machine’s origin, ensuring the input coordinates match the actual workpiece position. Skipping homing risks misalignment and scrap.

2. Q.: What if the CNC machine has no breakpoint protection function? How to manually record data accurately?

А: Используйте digital readout (DRO) or machine display to note XYZ coordinates. Для дополнительной точности, mark the tool tip position on the workpiece with a marker (only for non-critical surfaces) перед остановкой машины — это помогает проверить выравнивание при возобновлении работы.

3. Q.: Могу ли я использовать один и тот же процесс восстановления точки останова как для фрезерных, так и для токарных операций??

А: Основные шаги (запись данных, настройка инструмента) похожи, но поворот требует особой осторожности: Запишите угол шпинделя (для приводного инструмента) и компенсация радиуса вершины инструмента значение — влияет на точность резьбы или контура., которые менее критичны при фрезеровании.