Essential Precautions for High-Quality Plastic Injection Molded Parts

Plastic injection molding is a widely used manufacturing process, but producing high-quality parts requires attention to every detail. From material selection to post-processing, each step has its own precautions that directly affect the final product’s performance, появление, и стоимость. This article will break down the key precautions for each stage of plastic injection molded parts production to help you avoid common pitfalls and improve product quality.

1. Меры предосторожности по выбору материала

Choosing the right material is the foundation of making excellent plastic injection molded parts. The material must match the part’s intended use, performance requirements, and cost budget. Here’s a detailed breakdown of the key factors to consider:

2. Соображения дизайна

A reasonable part design not only simplifies the injection molding process but also improves the part’s quality and reduces defects. Here are the key design precautions:

• Равномерность толщины стенки: Uneven wall thickness causes uneven cooling and shrinkage, leading to warpage and sink marks. Keep the wall thickness as uniform as possible. If thickness variation is necessary, используйте постепенные переходы (НАПРИМЕР., конус) instead of sudden changes.
• Проект углов: Добавить рафы (обычно 1-5 градусы) to the part’s vertical surfaces. This helps the part eject smoothly from the mold and prevents scratches on the part surface. Без углах, the part may get stuck in the mold.
• Rib design: Ribs are used to enhance the part’s stiffness without increasing wall thickness. The height of the rib should not exceed 3 times the wall thickness, and the width should be 0.5-0.7 times the wall thickness. Также, add fillets at the rib’s root to avoid stress concentration.
• Bosses and supports: Bosses are used for assembly (НАПРИМЕР., screw holes). The diameter of the boss should be 2-3 times the diameter of the screw, and the height should not exceed 2 times the diameter. Add supporting ribs around the boss to prevent it from breaking.
• Undercuts and side actions: Подписаны (НАПРИМЕР., grooves on the side of the part) make the part hard to eject. Если необходимы подрезки, use side actions or slides in the mold. But this increases mold complexity and cost, so minimize undercuts when possible.
• Parting lines: The parting line is where the two halves of the mold meet. Design the parting line to be easy to process and remove flash. Avoid placing the parting line on the visible surface of the part to improve appearance.
• Gate and runner design: The gate is the channel through which the molten plastic enters the mold cavity. Choose the right gate type (НАПРИМЕР., edge gate, sprue gate) и размер. The runner should be designed to ensure uniform flow of molten plastic to each cavity. Shorten the runner length to reduce material waste.

3. Mold Maintenance and Inspection

The mold is the core tool of injection molding, and its condition directly affects the part’s quality and production efficiency. Regular maintenance and inspection are essential:

Routine Maintenance Tasks

1. Mold cleaning: Clean the mold cavity, бегун, and vent every 8-12 часы производства. Use a soft cloth or brush to remove plastic residues and dirt. Avoid using hard tools that may scratch the mold surface.
2. Corrosion prevention: Apply anti-rust oil to the mold surface when it’s not in use for a long time. For molds used in humid environments, use corrosion-resistant materials (НАПРИМЕР., нержавеющая сталь) for key components.
3. Venting check: Check the mold vents regularly. Clogged vents cause air trapping in the mold cavity, leading to bubbles and incomplete filling. Clean the vents with a small drill or needle if necessary.
4. Ejector pin maintenance: Lubricate the ejector pins every day to ensure smooth movement. Check for wear and bending of the ejector pins. Replace worn or bent pins in time to avoid damaging the part or the mold.

Periodic Inspection Items

4. Processing Parameters

Proper setting of processing parameters is crucial for obtaining high-quality parts. Even small deviations in parameters can cause defects. Here’s a guide to the key processing parameters:

Key Parameters and Their Effects

A common question: How to adjust processing parameters when facing warpage? Первый, check if the cooling time is sufficient. Если не, extend it. Затем, reduce the injection pressure and melt temperature to reduce internal stress. Также, ensure uniform wall thickness in the part design.

5. Контроль качества и тестирование

Quality control and testing throughout the production process ensure that only qualified parts leave the factory. Вот ключевой процесс:

Testing Items and Methods

• Точность размеров: Используйте суппорты, микрометры, и координировать измерительные машины (ШМ) to measure the part’s key dimensions. Compare the measured values with the design tolerances. Sampling frequency: 5 parts per hour for initial production, 2 parts per hour for stable production.
• Поверхностная отделка: Inspect the part surface with the naked eye and a magnifying glass (10х). Check for defects like scratches, пузырьки, вспышка, and sink marks. Reject parts with obvious surface defects.
• Warpage and shrinkage: Place the part on a flat surface to check warpage. Use a feeler gauge to measure the gap. For shrinkage, measure the part’s dimensions and calculate the shrinkage rate (compared to the mold size). The acceptable shrinkage rate varies by material (НАПРИМЕР., Стр: 1.5-2.5%, АБС: 0.5-0.8%).
• Flash and burrs: Check the part’s edges and parting lines for flash and burrs. Use a deburring tool to remove small burrs; reject parts with large flash.
• Material flow analysis: Use simulation software (НАПРИМЕР., Moldflow) to analyze the molten plastic flow in the mold cavity before production. Identify potential problems like short shots and uneven flow, and adjust the mold or processing parameters accordingly.
• Неразрушающее тестирование: Для критических частей (НАПРИМЕР., automotive and medical parts), use ultrasonic testing and X-ray testing to check for internal defects like voids and delamination.

6. Пост-обработка и отделка

Post-processing improves the part’s appearance, производительность, and assembly ability. Here are the key precautions:

• Выслушивание: Use manual deburring (файлы, наждачная бумага), mechanical deburring (rotary brushes), or ultrasonic deburring. Для точных частей, avoid excessive force during deburring to prevent deformation.
• Живопись и покрытие: Clean the part surface thoroughly before painting to remove oil and dust. Choose the right paint (НАПРИМЕР., acrylic paint for good adhesion, enamel paint for durability). Control the paint thickness (15-30 мкм) to avoid drips and uneven coating.
• Assembly considerations: Ensure the part’s assembly features (НАПРИМЕР., bosses, отверстия) meet the assembly requirements. Check the fit between parts; avoid over-tight or over-loose fits. Use appropriate assembly tools to prevent damaging the parts.
• Термическая обработка: Некоторые материалы (НАПРИМЕР., нейлон) need heat treatment (отжиг) Чтобы уменьшить внутренний стресс. Annealing conditions: Нагреть часть 80-100 ° C., держаться за 1-2 часы, Затем медленно охладитесь. This prevents warpage and cracking during use.
• Ультразвуковая сварка: Used to join two plastic parts. Control the welding time (0.5-2 с) и давление (10-30 Не) to ensure a strong weld without damaging the parts. The weld strength should be at least 80% of the base material strength.
• Laser marking: Used for marking logos, Серийные номера, and other information. Adjust the laser power (10-30 W.) и скорость (50-100 мм/с) to get clear and durable marks. Avoid marking on the part’s stress concentration areas.
• Поверхностная обработка: For parts needing better wear resistance or aesthetics, use surface treatments like electroplating (for metal-like appearance) и выстрелил (for improved surface hardness). Choose the right treatment method based on the material and requirements.

Yigu Technology’s View

В Yigu Technology, we believe that high-quality plastic injection molded parts come from strict control of every production link. Material selection should balance performance and cost; design should be mold-friendly; mold maintenance ensures stable production; processing parameters need precise adjustment; quality testing guarantees product reliability; post-processing enhances added value. We integrate these precautions into our production process, using advanced simulation tools and testing equipment to provide customers with high-quality parts.

FAQs

1. Q.: What should I do if the plastic injection molded part has bubbles?

А: Первый, check if the material is fully dried (especially for moisture-absorbing materials). Затем, inspect the mold vents for clogging and clean them if needed. Также, reduce the melt temperature and increase the injection speed slightly to avoid air trapping.

2. Q.: How to prevent warpage of plastic injection molded parts?

А: Ensure uniform wall thickness in the part design. Extend the cooling time to make the part cool evenly. Reduce the injection pressure and melt temperature to reduce internal stress. Также, check the mold alignment and adjust if necessary.

3. Q.: What factors affect the cost of plastic injection molded parts?

А: Key factors include material cost (resin type and recycled content), Стоимость плесени (complexity and material), processing cost (cycle time and energy consumption), and post-processing cost (рисование, сварка, и т. д.). Optimizing design (reducing undercuts) and processing parameters (shortening cycle time) can reduce costs.