3D printing is a mix of art and science—even experienced users face 3D printing forming failure from time to time. Whether your print lifts off the bed mid-print, has gaping layers, or comes out as a shapeless blob, these failures are frustrating—but almost always fixable. The key is to diagnose the root cause: it could be a misaligned bed, wrong temperature, faulty material, or even a drafty room. Это руководство разрушает 9 most common causes of 3D Печать forming failure, paired with step-by-step fixes and real-world examples. К концу, you’ll turn “failed print” into “perfect print” with confidence—no matter what material (Плата, Петг, АБС) or printer you use.
1. Uneven Print Bed: А #1 Cause of First-Layer Failure
A uneven print bed is the top reason 3D prints fail to form—if the bed isn’t flat, the first layer won’t adhere evenly, приводя к деформации, lifting, or missing sections.
What Happens & Почему
When the bed is uneven, some parts of the first layer are too close to the nozzle (causing over-extrusion and smearing) while others are too far (causing under-extrusion and gaps). Через некоторое время, the uneven adhesion makes the print lift off the bed entirely.
Исправить & Профилактика
| Шаг | Как это сделать | Инструменты необходимы |
|---|---|---|
| 1. Use Auto-Leveling | Run your printer’s auto-leveling function (most modern printers have this). It uses a sensor to map bed unevenness and adjust the Z-axis automatically. | Printer’s built-in sensor (НАПРИМЕР., BLTouch). |
| 2. Ручная корректировка | If no auto-leveling: Place a piece of A4 paper between the nozzle and bed. Adjust the bed’s 4 corner screws until the paper feels “slightly tight” when pulled. | A4 paper, screwdriver. |
| 3. Check Bed Flatness | For persistent issues: Use a straightedge or bed-leveling tool to check if the bed itself is warped. Replace the bed if it has visible dents or curves. | Straightedge, bed-leveling tool. |
Пример реального мира: A hobbyist printing a PLA phone case noticed the first layer lifted on one side. Running auto-leveling fixed the issue—but they later found the bed had a 0.2mm warp. Adding a glass bed on top of the original bed eliminated the problem for good.
2. Wrong Nozzle Height: Too Close or Too Far
Nozzle height (the distance between the nozzle and bed) is make-or-break for first-layer adhesion. Слишком близко, and the nozzle smears plastic; слишком далеко, and the plastic doesn’t stick.
What Happens & Почему
- Too Close: The nozzle scrapes the bed, smearing the first layer into a messy blob. This clogs the nozzle over time, leading to under-extrusion.
- Too Far: The plastic falls onto the bed without pressing down, so it doesn’t bond—resulting in a “spaghetti-like” first layer that won’t stay in place.
Исправить: Set Nozzle Height to A4 Paper Thickness
The ideal nozzle height is the thickness of a standard A4 sheet (≈0.1mm). Here’s how to set it:
- Heat the nozzle to your material’s printing temp (НАПРИМЕР., 190° C для PLA, 240° C для Petg).
- Lower the nozzle to the bed until it’s just above the surface.
- Slide an A4 paper between the nozzle and bed. Adjust the Z-axis until the paper moves with slight resistance—no more, не меньше.
Для чаевого: For PETG or ABS (which need stronger adhesion), set the nozzleslightly closer (≈0.08mm) than you would for PLA.
3. Incorrect Temperature Settings: Melting or Cooling Wrong
Temperature is critical for 3D printing—too cold, and the plastic won’t melt properly; Слишком горячий, and it won’t cool into shape. This affects every layer, not just the first.
Common Temperature Mistakes & Исправляет
| Материал | Общая проблема | Причина (Температура) | Исправить |
|---|---|---|---|
| Плата | First-layer lifting; weak adhesion | Bed temp too low (≤50°C) | Raise bed temp to 60–70°C; keep nozzle temp at 190–210°C. |
| Петг | Разделение слоя; деформация | Nozzle temp too low (≤220°C); bed temp too low (≤65°C) | Increase nozzle temp to 230–250°C; bed temp to 70–80°C. |
| АБС | Строка; bloating | Nozzle temp too high (≥250°C) | Lower nozzle temp to 220–240°C; use an enclosed printer to control cooling. |
What Happens When Temperature Is Wrong
- Too Cold (Плата): A maker printing a PLA vase set the bed temp to 50°C. The first layer lifted within 10 minutes—raising it to 65°C kept the vase anchored, and it printed perfectly.
- Too Hot (Петг): A student used 260°C for PETG (way above the 230–250°C range). The print had blobby edges and stringing—lowering to 240°C fixed the detail and reduced waste.
4. Extruder Issues: Clogs, Jams, or Uneven Flow
The extruder is the “heart” of your printer—it feeds plastic into the nozzle. If it’s clogged, jammed, or set to the wrong speed, plastic won’t flow evenly, leading to gaps, missing layers, or no extrusion at all.
3 Common Extruder Problems & Исправляет
| Проблема | Причина | Пошаговое исправление |
|---|---|---|
| Clogged Nozzle | Old plastic solidified in the nozzle; dirty filament. | 1. Heat nozzle to material temp (НАПРИМЕР., 240° C для Petg). 2. Push filament manually to clear the clog. 3. Use a needle to remove leftover plastic. |
| Uneven Extrusion | Extruder speed too fast/slow; loose extruder gear. | 1. Calibrate E-steps (follow your printer’s guide to set how much filament the extruder pushes). 2. Tighten the extruder gear’s screw if it’s loose. |
| Filament Jams | Tangled filament spool; filament diameter too thick. | 1. Stop the print and cut the tangled filament. 2. Check filament diameter (should match your printer’s specs: usually 1.75mm or 2.85mm). |
Тематическое исследование: A designer printing an ABS bracket noticed the extruder stopped feeding filament halfway through. They found the filament spool had a hidden tangle—fixing it and calibrating E-steps let them finish the print without starting over.
5. Low-Quality or Wet Filament: Хрупкий, Stringy, or Bubbly
Filament quality directly impacts print formation. Low-quality filament (with inconsistent diameter) or wet filament (with moisture) causes breaks, строка, and bubbles—all of which ruin the print.
How to Spot Bad Filament
- Low-Quality: Check for diameter variations (use calipers—should be ±0.05mm of the listed size). Inconsistent diameter leads to uneven extrusion.
- Wet Filament: Look for bubbles or popping sounds during printing (moisture turns to steam in the nozzle). Wet PLA/PETG also feels “sticky” instead of dry.
Исправить & Профилактика
| Action | Как это сделать | Инструменты необходимы |
|---|---|---|
| 1. Choose High-Quality Filament | Buy from trusted brands (НАПРИМЕР., Прусский, Hatchbox). Avoid cheap filament with no diameter specs. | None—just read reviews. |
| 2. Dry Filament | Используйте сушилку накаливания (60°C for 4–6 hours for PLA/PETG; 80° C для ABS). For DIY: Place filament in an oven at 40°C for 8 часы (no higher!). | Filament dryer or oven, desiccants. |
| 3. Store Properly | Keep unused filament in an airtight container with desiccants to absorb moisture. | Airtight container, desiccant packs. |
Пример: A maker’s PETG print had so many bubbles it looked like Swiss cheese. Drying the filament for 5 hours in a dryer eliminated the bubbles—now their prints are smooth and strong.
6. Slicer Software Mistakes: Wrong Settings = Wrong Print
Slicer software (НАПРИМЕР., Уход, Прусаслис) turns your 3D model into printer instructions. Wrong settings here—like layer height, скорость, or retraction—cause prints to fail before they even start.
Most Common Slicer Errors & Исправляет
| Параметр | Wrong Value | Исправить (Recommended Value) | Почему это важно |
|---|---|---|---|
| Высота слоя | Слишком толстый (≥0.3mm for small parts); Слишком тонкий (≤0.1mm for large parts) | 0.2mm for most prints; 0.15mm for details; 0.25mm for speed. | Thick layers = fast but rough; thin layers = slow but detailed. |
| Скорость печати | Too fast (≥80mm/s for PLA/PETG) | 40–60mm/s for PLA/PETG; 30–50mm/s for ABS. | Fast speed = no time for adhesion; slow speed = better layer bond. |
| Ретракция | Слишком низко (≤1 мм) or too high (≥4mm) | 2–3mm for PLA/PETG; 2.5–3.5mm for ABS. | Low retraction = stringing; high retraction = under-extrusion. |
Для чаевого: Use your printer’s “preset profiles” (НАПРИМЕР., Cura’s “PLA Generic” or “PETG Generic”) if you’re new—they’re optimized for most users. Only tweak settings once you understand their impact.
7. Environmental Factors: Drafts, Влажность, & Temperature Swings
Your printing environment matters more than you think. Drafts, высокая влажность, or sudden temperature changes can ruin even the best-calibrated print.
3 Environmental Culprits & Исправляет
| Проблема | Impact on Print | Исправить |
|---|---|---|
| Drafts | Rapid cooling causes layer separation and warping (especially for PETG/ABS). | Close windows/doors; use an enclosed printer or wrap an open printer in plastic sheeting. |
| High Humidity (>60%) | Moisture absorbed by filament leads to bubbles and weak layers. | Use a dehumidifier near the printer; store filament with desiccants. |
| Temperature Swings | Uneven cooling causes the print to shrink inconsistently. | Keep the room temp stable (20–25°C for PLA; 25–30°C for PETG/ABS). Avoid placing the printer near AC vents or heaters. |
Пример реального мира: A student printing a PETG drone frame in a drafty dorm room (18°C with open windows) had constant layer separation. Moving the printer to a closet (24° C., Нет черновиков) fixed the issue—now the frame holds together even when dropped.
8. Mechanical Failures: Stepper Motors, Belts, & Loose Parts
If your printer’s mechanical parts are faulty, no amount of calibration will save your print. Stepper motor issues, loose belts, or broken gears cause uneven movement, leading to misshapen prints.
Common Mechanical Issues & Исправляет
| Часть | Проблема | Исправить |
|---|---|---|
| Stepper Motors | Skipping steps (clicking sounds); uneven movement. | Check if the motor cables are loose—replug them. If clicking continues: Lower print speed (motors can’t keep up with fast speeds). |
| Belts | Loose belts (print shifts mid-print); tight belts (Нет движения). | Adjust belt tension: Loose belts = shift; tight belts = motor strain. Most printers have tension screws on the X/Y axes. |
| Loose Nozzle | Nozzle wiggles during printing; inconsistent extrusion. | Tighten the nozzle with a wrench (when cold!)—be careful not to over-tighten (this can damage the hotend). |
Предупреждение: If you hear strange noises (шлифование, clicking) from your printer, stop the print immediately—mechanical issues can damage the printer if left unfixed.
9. Warped Edges: When the Print Lifts Off the Bed
Warped edges (curled, lifted corners) are a common form of failure, especially with PETG and ABS. They happen when the material shrinks as it cools, pulling the edges away from the bed.
Почему это происходит & Как это исправить
| Исправить | Как это работает | Лучше всего для |
|---|---|---|
| 1. Add a Brim/Skirt | A brim (extra material around the print’s base) or skirt (material around the print, not attached) increases bed contact. | Large prints (НАПРИМЕР., плантаторы, мебель). |
| 2. Increase Bed Temp | Higher bed temp keeps the first layer warm longer, reducing shrinkage. | Петг (75–80 ° C.); АБС (90–110 ° C.). |
| 3. Use Adhesives | Glue stick, лак для волос, or specialized bed adhesives (НАПРИМЕР., Magigoo) improve adhesion for stubborn materials. | Glass beds; PETG/ABS prints. |
Пример: A maker’s ABS print had edges that lifted 1mm off the bed. Adding a 5mm brim and increasing the bed temp to 100°C kept the edges anchored—now the print lies perfectly flat.
Перспектива Yigu Technology
В Yigu Technology, Мы помогли 200+ clients fix 3D printing forming failure—most issues boil down to bed leveling, температура, or filament quality. Для начинающих, we recommend starting with PLA (most forgiving) and using auto-leveling + preset slicer profiles. For PETG/ABS, an enclosed printer and dried filament cut failure rates by 70%. Самая большая ошибка, которую мы видим? Skipping first-layer tests—print a 10cm square first to check adhesion; it saves hours of wasted time. 3D printing failure is part of the process—with the right fixes, you’ll turn frustration into success.
Часто задаваемые вопросы
- My print sticks to the bed too well—how do I remove it without breaking?Let the bed cool completely (Плата: 30–40 ° C.; PETG/ABS: 40–50 ° C.) before removing. If still stuck: Use a spatula (with a soft edge) to gently pry the print up, or heat the bed to 50°C (Плата) для 1 minute to loosen adhesion.
- Why does my print have gaps between layers even with correct temperature?Gaps usually mean under-extrusion. Проверять: 1) Is the filament tangled? 2) Is the extruder gear loose? 3) Is retraction too high? Fix these first—if gaps remain, increase nozzle temp by 5–10°C.
- Can a clogged nozzle be fixed, or do I need to replace it?Most clogs are fixable! Heat the nozzle to material temp, push filament manually to clear it, then use a needle to remove leftover plastic. For stubborn clogs (НАПРИМЕР., burnt PETG), soak the nozzle in acetone (for brass nozzles) на ночь. Replace only if the nozzle has cracks or worn threads.