What Is the Feed Rate Formula for Turning, and How Do You Use It?

Si vous êtes machiniste, amateur, or anyone working with lathes, Vous avez probablement demandé: “How do I calculate the right feed rate for turning?» The answer starts with a simple, critical formula—and knowing how to apply it correctly can mean the difference between a smooth, precise part and a ruined workpiece or damaged tool. Allons droit au but d’abord: the core feed rate formula for turning est:

Taux d'alimentation (Frousser) = Spindle Speed (N) × Feed per Revolution (f)

In plain language, this means your feed rate (how fast the tool moves along the workpiece, usually in inches per minute or millimeters per minute) is the product of how fast the spindle spins (revolutions per minute, RPM) and how much the tool advances with each spindle rotation (feed per rev, often in inches or millimeters).

Mais connaître la formule n'est qu'un début. Ci-dessous, we’ll break down what each component means, how to find the right values, erreurs courantes à éviter, and real-world examples to make sure you can apply this in your shop.

Understanding the Feed Rate Formula Components

Before you plug numbers into the formula, you need to know what each variable represents—and where to get accurate values for them. Let’s break down each part step by step.

1. Vitesse de broche (N): Revolutions Per Minute (RPM)

Spindle speed is how fast the workpiece rotates on the lathe. It’s determined by two key factors: le material of the workpiece (Par exemple, Aluminium vs. acier) et le tool material (Par exemple, high-speed steel/HSS vs. carbure). Running a spindle too fast can overheat the tool; too slow wastes time and leaves a rough finish.

To find the right RPM, you’ll use the vitesse de coupe (Vc)—a value that represents how fast the workpiece material moves past the cutting tool (measured in surface feet per minute, SFM, or meters per minute, m / mon). Cutting speeds are industry-standard and vary by material:

• Aluminium (doux): 300–800 SFM (pour outils en carbure)
• Acier doux (1018): 100–300 SFM (pour outils en carbure)
• Acier inoxydable (304): 50–150 SFM (pour outils en carbure)
• Titane: 20–50 SFM (pour outils en carbure)

Once you have the cutting speed, calculate RPM using this formula:

RPM (N) = (Vitesse de coupe × 12) / (π × Diamètre de la pièce)

(For metric: RPM = (Vitesse de coupe × 1000) / (π × Diamètre de la pièce))

Exemple: If you’re turning a 2-inch diameter mild steel workpiece with a carbide tool (vitesse de coupe = 200 SFM):

RPM = (200 × 12) / (3.14 × 2) = 2400 / 6.28 ≈ 382 RPM

2. Feed per Revolution (f): Inches or Millimeters per Spin

Feed per revolution (often called “chip load”) is how far the cutting tool advances along the workpiece with each full spindle rotation. This depends on three things:

• Type d'outil: A single-point turning tool (SPTT) will have a different feed than a threading tool.
• Tool material: Carbide tools can handle higher feeds than HSS.
• Desired finish: A roughing cut needs a higher feed (to remove material fast); a finishing cut needs a lower feed (pour une surface lisse).

Common feed per revolution values (for single-point turning tools):

• Brouillage (carbide on steel): 0.005–0.020 inches per revolution (DPI)
• Finition (carbide on steel): 0.001–0.005 IPR
• Aluminium (carbure): 0.003–0.030 IPR

Pour la pointe: Always check your tool manufacturer’s recommendations—they’ll list the maximum safe feed for their specific tool (Par exemple, a carbide insert might specify “max feed: 0.015 IPR for steel”).

Step-by-Step Guide to Calculating Feed Rate for Turning

Let’s put the formula into action with a real-world example. Suppose you’re tasked with turning a 1.5-inch diameter aluminum rod (6061-T6) using a carbide single-point tool. Here’s how to find the feed rate:

Étape 1: Choose the Right Cutting Speed (Vc)

For 6061-T6 aluminum and carbide tools, the industry standard cutting speed is 500 SFM (check your tool catalog to confirm—some premium carbides can go higher, jusqu'à 800 SFM).

Étape 2: Calculate Spindle Speed (RPM)

Use the RPM formula for inches:

RPM = (Vc × 12) / (π × Diamètre)

RPM = (500 × 12) / (3.14 × 1.5) = 6000 / 4.71 ≈ 1274 RPM

Étape 3: Select Feed per Revolution (f)

Since this is a roughing cut (we want to remove material quickly), we’ll use a feed of 0.015 DPI (within the safe range for carbide on aluminum).

Étape 4: Apply the Feed Rate Formula

FR = N × f

FR = 1274 RPM × 0.015 IPR = 19.11 inches per minute (Ipm)

Étape 5: Adjust for Real-World Conditions

If the aluminum rod is slightly warped, or if your lathe has vibration issues, you might lower the feed to 0.012 IPR to avoid tool chatter. That would make the feed rate: 1274 × 0.012 = 15.29 Ipm.

Étude de cas: A machinist at a small shop once skipped Step 5—they used the full 0.015 IPR on a warped aluminum workpiece. The vibration caused the tool to “bounce,” leaving deep grooves in the part and wearing down the carbide insert in 10 minutes (instead of the expected 2 heures). By reducing the feed to 0.010 DPI, they fixed the chatter and extended tool life.

How Material and Tool Type Affect Feed Rate Calculations

Not all materials or tools are the same—and that means your feed rate will change drastically depending on what you’re cutting and what you’re cutting with. Let’s compare two common scenarios to see the difference.

Key takeaways from the table:

• Matériaux plus durs (acier inoxydable) need lower cutting speeds and feeds than softer ones (aluminium).
• Outils HSS (moins cher mais moins durable) require slower RPM and lower feeds than carbide tools.
• Finishing cuts use much lower feeds than roughing cuts to achieve a smooth surface (Valeur RA).

Common Mistakes When Using the Feed Rate Formula (Et comment les éviter)

Even experienced machinists make errors with feed rate calculations. Here are the most frequent mistakes and how to fix them:

1. Using Outdated Cutting Speeds

Many beginners rely on old handbooks that list cutting speeds for HSS tools—but if you’re using carbide, those values are too low. Par exemple, a 1980s guide might say 100 SFM for steel and HSS, but modern carbide can handle 200–300 SFM.

Réparer: Use your tool manufacturer’s website or latest catalog (Par exemple, Sandvik, Kennametal) for cutting speeds—they update these as new tool materials are developed.

2. Ignoring Tool Wear

As a tool wears down (you’ll see a dull edge or increased heat), its ability to handle high feeds decreases. If you keep using the same feed rate, you’ll get a rough finish or even break the tool.

Réparer: Check the tool every 10–15 minutes during long runs. If the finish gets worse, lower the feed by 10–20% or replace the tool.

3. Forgetting the Workpiece Diameter

The RPM formula depends on the workpiece’s diameter—if you use the wrong diameter (Par exemple, the stock diameter instead of the finished diameter), your RPM will be off. Par exemple, turning a 3-inch stock down to 2 pouces: utiliser 3 inches for the initial roughing cuts (since the tool is cutting the outer, larger diameter) et 2 inches for finishing.

Réparer: Measure the workpiece diameter before each cut, especially if you’re reducing the size in multiple passes.

4. Confusing Inches and Metric Units

Mixing IPR and millimeters per revolution (MM / REV) is a easy mistake. Par exemple, en utilisant 0.1 MM / REV (which is ~0.004 IPR) comme 0.1 IPR will result in a feed rate that’s 25x too high—ruining the tool.

Réparer: Label your tools and notes clearly (Par exemple, “0.010 IPR” or “0.25 mm/rev”) and double-check units before calculating.

Advanced Tips for Optimizing Feed Rate (From Industry Experts)

Once you master the basics, these pro tips will help you get better results, gagner du temps, and extend tool life:

1. Use Constant Surface Speed (CSS) if Your Lathe Has It

Many modern CNC lathes have a CSS feature that automatically adjusts the spindle speed as the workpiece diameter decreases (Par exemple, when tapering or facing). This keeps the cutting speed (SFM) cohérent, which means you can maintain a steady feed rate without recalculating RPM.

Exemple: When facing a 4-inch diameter steel disk down to 1 pouce, CSS will lower the RPM from ~191 (pour 4 pouces, 200 SFM) to ~764 (pour 1 pouce, 200 SFM)—ensuring the tool always cuts at the optimal speed.

2. Adjust Feed Rate for Deep Cuts

If you’re making a deep cut (Par exemple, 0.5 pouces de profondeur), the tool has more contact with the workpiece, which generates more heat. To prevent tool failure, lower the feed rate by 30–50% compared to a shallow cut (0.1 pouces de profondeur).

Avis d'expert: “I once had a 学徒 (apprentice) run a 0.4-inch deep cut on steel with a 0.015 IPR feed— the tool melted in 2 minutes,” says Mike Torres, a senior machinist with 25 années d'expérience. “We lowered the feed to 0.008 DPI, and the same tool lasted 3 heures."

3. Test Feeds on Scrap Material First

Never use a new feed rate on a critical part. Plutôt, test it on a scrap piece of the same material. Par exemple, if you’re trying a 0.020 IPR feed on aluminum, first run it on a scrap aluminum rod. Check for chatter, usure, and finish quality—adjust as needed before moving to the actual part.

Yigu Technology’s Perspective on Feed Rate Calculation for Turning

À la technologie Yigu, we believe the feed rate formula for turning is more than just a math equation—it’s a foundation for efficient, high-quality machining. In our work with manufacturers (from automotive to aerospace), we’ve seen how small feed rate adjustments can reduce production time by 15–20% while cutting tool costs by 30%.

One key insight we’ve gained: many shops rely too heavily on “rules of thumb” instead of data. Par exemple, a shop might use 0.010 IPR for all steel cuts, but with modern carbide tools and CSS lathes, they could safely use 0.012–0.014 IPR for roughing—saving hours per week. We recommend combining the feed rate formula with real-time monitoring (Par exemple, tool temperature sensors) to find the sweet spot between speed and tool life.

Finalement, the best feed rate isn’t just the one that fits the formula—it’s the one that balances your specific goals: finish quality, vitesse de production, and tool budget.

FAQ: Common Questions About the Feed Rate Formula for Turning

1. What if my lathe uses metric units (mm/min instead of IPM)?

The formula stays the same—just use metric values. Par exemple:

• Vitesse de broche (N) = (Cutting Speed in m/min × 1000) / (π × Workpiece Diameter in mm)
• Feed per revolution (f) = mm/rev
• Taux d'alimentation (Frousser) = N (RPM) × f (MM / REV) = mm/min

Exemple: Cutting a 30mm diameter steel bar with a cutting speed of 60 m/min and feed of 0.2 MM / REV:

RPM = (60 × 1000) / (3.14 × 30) ≈ 637 RPM

FR = 637 × 0.2 = 127.4 mm / min

2. Can I use the same feed rate for threading and turning?

No—threading requires a much more precise feed rate (equal to the thread pitch). Par exemple, un 1/4-20 thread (20 threads per inch) needs a feed rate of 0.05 DPI (1/20 = 0.05). Using a higher or lower feed will ruin the thread.

3. How do I know if my feed rate is too high?

Signs of a too-high feed rate include:

• Tool chatter (vibration that leaves a wavy finish)
• Excessive heat (the tool or workpiece feels hot to the touch)
• Usure (dull edge, brouillage, ou décoloration)
• Finition de surface rugueuse (high Ra value)

4. Do I need to adjust feed rate for different lathe sizes?

Yes—small benchtop lathes (Par exemple, 10-inch swing) have less power than large industrial lathes. If your small lathe struggles with a 19 IPM feed rate, lower it by 20–30% to avoid stalling the spindle.

5. Where can I find reliable cutting speed and feed data?

The best sources are:

• Tool manufacturer websites (Sandvik Coromant, Kennametal, Walter Tools)
• Machining handbooks (Par exemple, Machinery’s Handbook)
• Industry associations (Par exemple, SME—Society of Manufacturing Engineers)